>

Hyundai Equus: Coolant Repair procedures - Cooling System - Engine Mechanical System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Coolant Repair procedures

Engine Coolant Refilling And Bleeding
   
Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.
   
When pouring engine coolant, be sure to shut the relay box lid and not to let coolant spill on the electrical parts or the paint. If any coolant spills, rinse it off immediately.
1.
Make sure the engine and radiator are cool to the touch.
2.
Loosen the drain plug (A) and drain the engine coolant. Remove the radiator cap (B) to speed draining.
   
Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.

3.
Tighten the radiator drain plug securely after draining engine coolant.
4.
After draining engine coolant in the reservoir tank, clean the tank.
5.
Fill the radiator with water through the radiator cap and tighten the cap.
   
To most effectively bleed the air, pour the water slowly and press on the upper/lower radiator hoses.
6.
Start the engine and allow to come to normal operating temperature. Wait for the cooling fans to turn on several times. Accelerate the engine to aid in purging trapped air. Shut engine off.
7.
Wait until the engine is cool.
8.
Repeat steps 1 to 7 until the drained water runs clear.
9.
Fill fluid mixture with coolant and water (55~60%) (except for North America, Europe and China : 45~50%) slowly through the radiator cap. Push the upper/lower hoses of the radiator so as bleed air easily.
   
Use only genuine antifreeze/coolant.
For best corrosion protection, the coolant concentration must be maintained year-round at 55% (except for North America, Europe and China : 45%) minimum.
Coolant concentrations less than 55% (except for North America, Europe and China : 45%) may not provide sufficient protection against corrosion or freezing.
Coolant concentrations greater then 60% will impair cooling efficiency and are not recommended.
   
Do not mix different brands of antifreeze/coolants.
Do not use additional rust inhibitors or antirust products; they may not be compatible with the coolant.
10.
Start the engine and run coolant circulates.
When the cooling fan operates and coolant circulates, refill coolant through the radiator cap.
11.
Repeat 10 until the cooling fan 3~5 times and bleed air sufficiently out of the cooling system.
12.
Install the radiator cap and fill the reservoir tank to the "MAX" line with coolant.
13.
Run the vehicle under idle until the cooling fan operates 2~3 times.
14.
Stop the engine and wait coolant gets cool.
15.
Repeat 9 to 14 until the coolant level doesn't fall any more, bleed air out of the cooling system.
   
As it is to bleed air out to the cooling system and refill coolant when coolant gets cool completely, recheck the coolant level in the reservoir tank for 2~3 days after replacing coolant.

Coolant capacity :
12.1L (12.78 US qt, 10.64 lmp qt, 3.194 US.gal)

    Cooling System
    ...

    Radiator Components and Components Location
    Components 1. Cooling fan assembly2. Radiator lower hose3. Radiator upper hose4. Coolant reservoir tank5. Radiator6. Mounting insulator7. Mounting bracket ...

    See also:

    Engine number
    The engine number is stamped on the engine block as shown in the drawing. ...

    Evaporator Core Repair procedures
    Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the heater and blower assembly. (Refer to Heater -"Heater Unit") 3. Remove the heater unit lower case (A) after loos ...

    Middle Speed Sensor Description and Operation
    Description The middle speed sensor measures the rate of rotation of the 6C outer drum inside the transmission and delivers the readings to the TCM. ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com