>

Hyundai Equus: Defogging logic - Windshield defrosting and defogging - Features of your vehicle - Hyundai Equus 2009-2024 Owners ManualHyundai Equus: Defogging logic

To reduce the possibility of fogging up the inside of the windshield, the air intake is controlled automatically according to certain conditions such as position. To cancel or return the defogging or
logic, perform the following steps:position. To cancel or return the defogging
logic, perform the following steps:

1. Turn the Engine Start/Stop Button to the ON position.


1. Turn the Engine Start/Stop Button to the ON position.
2. Select the defrost position pressing defrost button ( 3. While holding the air conditioning button (A/C) pressed, press the air intake ).

3. While holding the air conditioning button (A/C) pressed, press the air intake control button at least 5 times within 3 seconds.

The indicator on the air intake control button blinks 3 times with 0.5 second of interval. It indicates that the defogging logic is canceled or returned to the programmed status.

If the battery has been discharged or disconnected, the system resets to the preprogrammed defogging logic

Auto defogging system (if equipped)

Auto defogging reduces the probability of fogging up the inside of the windshield


Auto defogging reduces the probability of fogging up the inside of the windshield by automatically sensing the moisture on the inside of the windshield.

The auto defogging system operates when the heater or air conditioning is on.

This indicator illuminates when the auto defogging system senses the moisture


This indicator illuminates when the auto defogging system senses the moisture on the inside of the windshield and operates.

If more moisture is in the vehicle, the automated steps operate as follows: If auto defogging does not defog the window at step 1, outside air position, step 2, blowing air toward the windshield occurs.

Step 1 : Outside air position

Step 2 : Operating the air conditioning

Step 3 : Blowing air toward the windshield

Step 4 : Increasing air flow toward the windshield

The auto defogging system is automatically activated when the conditions are met. However, if you would like to cancel the auto defogging system, press the front defroster button 4 times within 2 seconds while pressing the AUTO button. The indicator of the front defroster button will blink 3 times to notify you that the system is cancelled. To use the auto defogging system again, follow the procedures mentioned above.

If the battery has been disconnected or discharged, it resets to the auto defogging status.

✽ NOTICE

When the air conditioning is turned on and the outside air position is selected by the auto defogging system, if you try to turn off the air conditioning and select the recirculated air position, the indicator will blink 3 times and the air conditioning will not be turned off and recirculated air position will not be selected.

CAUTION

Do not remove the sensor cover located on the upper end of the driver side windshield glass. Damage to system parts could occur and may not be covered by your vehicle warranty.

    Windshield defrosting and defogging
    WARNING - Windshield heating Do not use the or position during cooling operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshiel ...

    Storage compartments
    These compartments can be used to store small items required by the driver or passengers. CAUTION To avoid possible theft, do not leave valuables in the storage compartments. Always keep the ...

    See also:

    Compressor Schematic Diagrams
    Circuit diagram 1. Air compressor connector [Motor power connector (A)][Exhaust valve connector (B)][Temperature sensor connector (C)] 2. Air compressor terminal function [Motor power] ...

    Cool and Warm Box Description and Operation
    Description Cool and warm box is a compartment where you can keep items cool or warm. The sytem is a enviromentally friendly system that operates independently from the heater and A/C system. ...

    Brake Pedal Repair procedures
    Removal 1. Remove the lower crash pad. (Refer to Body - "Crash Pad") 2. Disconnect the stop lamp switch connector (A). 3. Remove the mounting bracket nut (B). Tightening torque : 14. ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com