>
Hyundai Equus Manuals

Hyundai Equus: Engine And Transmission Assembly Repair procedures - Engine And Transmission Assembly - Engine Mechanical System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Engine And Transmission Assembly Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Engine Mechanical System / Engine And Transmission Assembly / Engine And Transmission Assembly Repair procedures

Removal
   
•
Use fender covers to avoid damaging painted surfaces.
•
To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
   
•
Mark all wiring and hoses to avoid misconnection.
•
For release the fuel system pressure before remove the engine assembly, start the engine without fuel pump relay. And then turn off the ignition switch after engine stops.
1.
Remove the transmission before removing the engine. (Refer to AT group)
2.
Disconnect the battery negative cable (A).
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

3.
Remove the engine room cover (A), engine cover (B) and radiator grill upper cover (C).

4.
Loosen the drain plug (A) and drain the engine coolant. Remove the radiator cap to speed draining.
   
Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.

5.
Remove the air cleaner assembly.
(1)
Remove the air duct (A).
(2)
Disconnect the breather hose (B).
(3)
Loosen the clamp (C) and then disconnect the air intake hose from the throttle body.
Tightening torque :
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)
(4)
Remove the chamber air cleaner (D) and air cleaner assembly (E).
Tightening torque
Air cleaner assembly bolts:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

6.
Recover refrigerant and then disconnect the A/C high pressure pipe (A) and low pressure pipe (B). (Refer to Air conditioner compressor in HA Group)

7.
Remove the front wheel.
8.
Remove the under cover.
9.
Disconnect the radiator upper hose (A) and lower hose (B).

10.
Disconnect the ATF oil cooler hose (A).

11.
Remove the fuel hose (A), the purge control solenoid valve (PCSV) hose (B) and the brake booster vacuum hose (C).

12.
Disconnect the heater hoses (A).

13.
Disconnect the ECM connector (A), TCM connector (B), IDB connector (C), front connector (D) and ground line (E).
Tightening torque
Ground (E) :
10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 7.9 ~ 10.1 lb-ft)

14.
Remove the fuse box cover (A).

15.
Disconnect the wiring (A) of the fuse box.

16.
Remove the jump cable cover (A) and fuse & relay box cover (B).

17.
Disconnect the wiring (A) of the jump cable and the wiring (B) of the fuse & relay box .

18.
Remove the fuse & relay box (A) by loosening the mounting bolts (B).

19.
Remove the connector (A) and wirings.

20.
Disconnect the ground cable (A).
Tightening torque :
10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 7.9 ~ 10.1 lb-ft)

21.
Remove the tie rod end ball joint (A). (Refer to ST group)
22.
Remove the stabilizer bar by loosening the link fixing nut (B) and clamp fixing bolt (C). (Refer to SS group)
23.
Remove the air spring wiring bracket (D)
24.
Remove the shock absorber lower mounting bolt and nut (E). (Refer to SS group)
25.
Remove the height level sensor mounting bolt (F).
26.
Remove the lateral arm mounting bolt & nut (G) from the sub frame. (Refer to SS group)
27.
Remove the tension arm mounting bolt & nut (H) from the sub frame. (Refer to SS group)

28.
Disconnect the power steering fluid hoses (A) and then drain the power steering fluid.
(Refer to ST group)
29.
Remove the air hose fixing clips (B) from the sub frame.

30.
Remove the steering column U-joint bolt (A). (Refer to ST group)

31.
Disconnect the LH and RH rear oxygen sensors (A) and then front muffler (C) after removing the exhaust manifold stay (B).
Tightening torque
Nuts (D):
49.1 ~ 54.0 N.m (5.0 ~ 5.5 kgf.m, 36.2 ~ 39.8 lb-ft)
Bolts (E):
34.3 ~ 41.2 N.m (3.5 ~ 4.2 kgf.m, 25.3 ~ 30.4 lb-ft)

32.
Support the sub frame (A) and engine assembly with a floor jack.
33.
Remove the sub frame mounting bolts (B).
Tightening torque :
137.3 ~ 156.9 N.m (14.0 ~ 16.0 kgf.m, 101.3 ~ 115.7 lb-ft)
   
•
After removing the mounting bolts, the engine assembly may fall downward, and so support them securely with floor jack.
•
Verify that the hoses and connectors are disconnected before removing the engine assembly.

[Front]

[Center]

[Rear]

34.
Remove the engine assembly and sub frame by lifting vehicle.

   
When removing the engine assembly, be careful not to damage any surrounding parts or body components.
Installation
Installation is in the reverse order of removal.
Perform the following :
•
Adjust the shift cable.
•
Refill engine with engine oil.
•
Refill transaxle with fluid.
•
Clean battery posts and cable terminals with sandpaper. Reassemble, then apply grease to prevent corrosion
•
Inspect for fuel leakage.
-
After assembling the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
-
Repeat this operation two or three times, then check for fuel leakage at any point in the fuel lines.
•
Refill radiator with engine coolant.
•
Bleed air from the cooling system.
-
Start engine and let it run until it warms up. (Until the radiator fan operates 3 or 4 times.)
-
Turn Off the engine and let it cool down. Check the level in the radiator, add coolant if needed. This will allow trapped air to be removed from the cooling system.
-
Put radiator cap on tightly, then run the engine again and check for leaks.
    Engine Mounting Components and Components Location
    Components 1. Engine mounting insulator2. Engine support bracket LH3. Engine support bracket RH4. Transmission mounting insulator ...

    Timing System
    ...

    See also:

    Curtain Airbag (CAB) Module Components and Components Location
    Components ...

    Repair procedures
    Removal 1. Remove the front bumper cover. (Refer to Body - "Front Bumper Cover") 2. Remove the bolts and disconnect the horn connectors, then remove the high pitch horn (A) and low pitch horn ...

    Rear Glass Defogger Printed Heater Repair procedures
    Inspection     Wrap tin foil around the end of the voltmeter test lead to prevent damaging the heater line. Apply finger pressure on the tin foil, moving the tin foil along th ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com