Specifications |
Items | Specification |
Air spring volume at design position | 1.78x |
Maximum other bellow diameter | 118 mm |
Burst pressure | 31.5 bar |
Minimum operating temperature | -40°C |
Maximum operating temperature | 80°C |
Items | Specification |
Operation voltage | 9 ~ 15 VDC |
Max. perm. Current | 35 A Min |
Lower operation temperature | -40°C |
Upper operation temperature | 70°C |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Operation voltage | 9 ~ 15 VDC |
Lower operation temperature | -40°C |
Upper operation temperature | 70°C |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Required supply voltage | 5 VDC 5% |
Operation voltage | 5 VDC 10% |
Maximum allowed voltage range | 20 V |
Storage Temperature | -40°C ~ 90°C |
Items | Specification |
Operating pressure | 16.5 bar |
Burst pressure | 40 bar min |
Air tank volume | 5.2 x |
Items | Specification |
Rated Voltage | 12 V DC |
Operating Voltage | 10 ~ 16 V DC |
Operation Temperature | -40°C ~ 75°C |
Storage Temperature | -40°C ~ 90°C |
Item | Tightening torque (kgf.m) | ||
N.m | kgf.m | lb-ft | |
Reservoir tank to crash box | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Reservoir tank to frame housing | 20.0 ~ 30.0 | 2.0 ~ 3.0 | 14.0 ~ 22.0 |
Front height sensor to frame | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Front height sensor to lateral arm | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Solenoid valve to bracket | 8.0 ~ 12.0 | 0.8 ~ 1.2 | 6.0 ~ 9.0 |
Compressor to bracket | 8.0 ~ 12.0 | 0.8 ~ 1.2 | 6.0 ~ 9.0 |
G-sensor to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Compressor & bracket to frame crash box | 35.0 ~ 55.0 | 3.5 ~ 5.5 | 25.0 ~ 40.0 |
Air filter to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Front height sensor to frame | 4.0 ~ 6.0 | 0.4 ~ 0.6 | 3.0 ~ 4.0 |
Feeling valve mounting bracket to frame | 17.0 ~ 26.0 | 1.7 ~ 2.6 | 12.0 ~ 19.0 |
Components and Components Location
Components
1. Glass panel2. Decoration cover3. Drip link4. Guide assembly5. Drip rail6. Sunshade7. Defector8. Defector link 9. Seal tape10. Motor11. Frame12. Set plate
...
Cup holder
WARNING - Hot liquids
Do not place uncovered cups of hot liquid in the cup holder while the
vehicle is in motion. If the hot liquid spills, you could be burned. Such a
burn to the driver cou ...
Rear Seat Belt Retractor Repair procedures
Replacement
•
When installing the belt, make sure not to damage the retractor.
1.
Remove the rear package tray trim.
(Refer to Interior Trim - "Rear Package Tray T ...