>
Hyundai Equus Manuals

Hyundai Equus: Repair procedures - Air Conditioning System - Heating, Ventilation and Air Conditioning - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Heating, Ventilation and Air Conditioning / Air Conditioning System / Repair procedures

Refrigerant System Service Basics
Refrigerant Recovery
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.
   
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate the work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
Connect a R-134a refrigerant
Recovery/Recycling/Charging system (A) to the high-pressure service port (C) and the low-pressure service port (B) as shown, following the equipment manufacturer's instructions.

2.
Measure the amount of refrigerant oil removed from the A/C system after the recovery process is completed. Be sure to install the same amount of new refrigerant oil back into the A/C system before charging.
System Evacuation
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a(R-134a) from the air conditioning system.
   
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate the work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
When an A/C system has been opened to the atmosphere, such as during installation or repair, it must be evacuated using a R-134a refrigerant Recovery/Recycling/Charging system. (If the system has been open for several days, the receiver/drier should be replaced, and the system should be evacuated for several hours.)
2.
Connect a R-134a refrigerant Recovery/Recycling/Charging system (A) to the high-pressure service port (C) and the low-pressure service port (B) as shown, following the equipment manufacturer's instructions.

3.
If the low-pressure does not reach more than 93.3 kPa (700 mmHg, 27.6 in.Hg) in 10 minutes, there is probably a leak in the system. Partially charge the system, and check for leaks (see Refrigerant Leak Test.)
4.
Remove the low pressure valve from the low-pressure service port.
System Charging
Use only service equipment that is U.L-listed and is certified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system.
   
•
Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
•
Be careful when connecting service equipment.
•
Do not breathe refrigerant or vapor.
If accidental system discharge occurs, ventilate the work area before resume of service.
Additional health and safety information may be obtained from the refrigerant and lubricant manufacturers.
1.
Connect a R-134a refrigerant
Recovery/Recycling/Charging system (A) to the high-pressure service port (C) as shown, following the equipment manufacturer's instructions.

2.
Add the same amount of new refrigerant oil to the system that was removed during recovery. Use only specified refrigerant oil. Charge the system with R-134a refrigerant [700±25g (24.7±0.88oz.)]. Do not overcharge the system the compressor will be damaged.
Refrigerant Leak Test
Always conduct a leak test with an electronic leak detector whenever leakage or refrigerant is suspected and when conducting service operations which are accompanied by disassembly or loosening or connection fittings.
   
In order to use the leak detector properly, read the manual supplied by the manufacturer.
If a gas leak is detected, proceed as follows:
1.
Check the torque on the connection fittings and, if too loose, tighten to the proper torque. Check for gas leakage with a leak detector (A).
2.
If leakage continues even after the fitting has been tightened, discharge the refrigerant from the system, disconnect the fittings, and check their seating faces for damage. Always replace, even if the damage is slight.
3.
Check the compressor oil and add oil if required.
4.
Charge the system and recheck for gas leaks. If no leaks are found, evacuate and charge the system again.

    Description and Operation
    Refrigeration Cycle ...

    Components and Components Location
    Component Location Index Engine Room 1. Receiver-drier2. Condenser3. Ambient Temperature Sensor4. Compressor5. Discharge Hose6. Suction & Liquid Tube Assembly7. Service Port (Low Pressure)8. ...

    See also:

    Specifications
    Specification Ignition System Ignition Coil ItemSpecification Primary Coil Resistance (x)0.62 ± 10% [20°C (68°F)]Secondary Coil Resistance (kx)7.0 ± 15% [20°C (68°F)] Spark Plug ItemS ...

    Blower Motor Repair procedures
    Inspection 1. Connect the battery voltage and check the blower motor rotation. 2. If the blower motor does not operate well, substitute with a known-good blower motor and check for proper oper ...

    Front Air Strut Assembly Description and Operation
    Description The air spring & damper is one unit so that it is not possible to make separation. The average pressure of front air spring is around 7.5 bar. When the front air spring is delive ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com