Hyundai Equus: Engine Control Module (ECM) Repair procedures
Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Engine Control/Fuel System / Engine Control System / Engine Control Module (ECM) Repair procedures
| Removal |
When replacing the ECM, the vehicle equipped with the immobilizer must be performed procedure as below.
[In the case of installing used ECM]
1) Perform "ECM Neutral mode" procedure with GDS. (Refer to "Immobilizer" in BE group)
2) After finishing "ECM Neutral mode", perform "Key teaching" procedure with GDS. (Refer to "Immobilizer" in BE group)
[In the case of installing new ECM]
Perform "Key teaching" procedure with GDS. (Refer to "Immobilizer" in BE group)
|
When replacing the ECM, the vehicle equipped with the smart key system (Button start) must be performed procedure as below.
[In the case of installing used ECM]
1) Perform "ECM Neutral mode" procedure with GDS. (Refer to "Smart key" in BE group)
2) After finishing "ECM Neutral mode", insert the key (or
press the start button) and turn it to the IGN ON and OFF position. Then
the ECM learns the smart key information automatically.
[In the case of installing new ECM]
Insert the key (or press the start button) and turn it to the
IGN ON and OFF position. Then the ECM learns the smart key information
automatically.
|
| 1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable. |
| 2. |
Remove the ECM & TCM cover (A).
|
| 3. |
Disconnect the front harness (A), and then disconnect the ECM connector (B) and the TCM connector (C). |
| 4. |
Remove the harness installation nut (D) and ground bolt (E), and then remove the harness (F). |
| 5. |
Remove the ECM & TCM bracket installation bolts (G) and nut (H).
|
| 6. |
After removing the installation nuts (A), remove the TCM (B) from the bracket
|
| 7. |
After removing the installation nuts (A), remove the ECM (B) from the bracket
|
| Installation |
When replacing the ECM, the vehicle equipped with the immobilizer must be performed procedure as below.
[In the case of installing used ECM]
1) Perform "ECM Neutral mode" procedure with GDS. (Refer to "Immobilizer" in BE group)
2) After finishing "ECM Neutral mode", perform "Key teaching" procedure with GDS. (Refer to "Immobilizer" in BE group)
[In the case of installing new ECM]
Perform "Key teaching" procedure with GDS. (Refer to "Immobilizer" in BE group)
|
When replacing the ECM, the vehicle equipped with the smart key system (Button start) must be performed procedure as below.
[In the case of installing used ECM]
1) Perform "ECM Neutral mode" procedure with GDS. (Refer to "Smart key" in BE group)
2) After finishing "ECM Neutral mode", insert the key (or
press the start button) and turn it to the IGN ON and OFF position. Then
the ECM learns the smart key information automatically.
[In the case of installing new ECM]
Insert the key (or press the start button) and turn it to the
IGN ON and OFF position. Then the ECM learns the smart key information
automatically.
|
| 1. |
Install in the reverse order of removal.
|
| ECM Problem Inspection Procedure |
| 1. |
TEST ECM GROUND CIRCUIT: Measure resistance between ECM and
chassis ground using the backside of ECM harness connector as ECM side
check point. If the problem is found, repair it.
|
| 2. |
TEST ECM CONNECTOR: Disconnect the ECM connector and visually
check the ground terminals on ECM side and harness side for bent pins
or poor contact pressure. If the problem is found, repair it. |
| 3. |
If problem is not found in Step 1 and 2, the ECM could be
faulty. If so, replace the ECM with a new one, and then check the
vehicle again. If the vehicle operates normally then the problem was
likely with the ECM. |
| 4. |
RE-TEST THE ORIGINAL ECM: Install the original ECM (may be
broken) into a known-good vehicle and check the vehicle. If the problem
occurs again, replace the original ECM with a new one. If problem does
not occur, this is intermittent problem (Refer to “Intermittent
Problem Inspection Procedure” in Basic Inspection Procedure). |
| VIN programming procedure |
VIN (Vehicle Identification Number) is a number that has the
vehicle's information (Maker, Vehicle Type, Vehicle Line/Series, Body
Type, Engine Type, Transmission Type, Model Year, Plant Location and so
forth. For more information, please refer to the group "GI" in this
SERVICE MANUAL). When replacing an ECM, the VIN must be programmed in
the ECM. If there is no VIN in ECM memory, the fault code (DTC P0630) is
set.
The programmed VIN cannot be changed. When writing the VIN, confirm the VIN carefully. |
| 1. |
Select "VIN Writing" function in "Vehicle S/W Management". |
| 2. |
Select "Write VIN" in "ID Resister".
|
| 3. |
Input the VIN.
|
| 4. |
Turn the ignition switch OFF, then back ON. |
Engine Control Module (ECM) Schematic Diagrams
ECM Terminal And Input / Output signal
ECM Harness Connector
ECM Terminal Function
Connector [C200-A]
Pin No.DescriptionConnected to1Ignition Coil (Cylinder #3) control outputIgnition Coil ( ...
Injector Drive Box (IDB) Schematic Diagrams
Injector Drive Box (IDB)
IDB Connector
ECM Terminal Function
Connector [C200-IDB]
Pin No.DescriptionConnected to1ECM groundChassis ground2ECM groundChassis ground3Battery power (B+)Main rela ...
See also:
Rear Seat Back Cover Repair procedures
Replacement
[LH]
•
Put on gloves to protect your hands.
•
When prying with a flat-tip screwdriver, wrap it with
protective tape, and app ...
Fuel Pressure Control Valve Specifications
Specification
ItemSpecificationCoil Resistance (x)0.47 ~ 0.51 [20°C(68°F)]
...
Power outlet
The power outlet is designed to provide power for mobile telephones or other
devices designed to operate with vehicle electrical systems. The devices should
draw less than 10 amps with the engin ...
Categories
Hyundai Equus Manuals
© 2011-2025 Copyright www.heqmanual.com