>
Hyundai Equus Manuals

Hyundai Equus: Heated Oxygen Sensor (HO2S) Repair procedures - Engine Control System - Engine Control/Fuel System - Hyundai Equus VI 2009-2025 Service ManualHyundai Equus: Heated Oxygen Sensor (HO2S) Repair procedures

Second generation VI (2009–2025) / Hyundai Equus VI 2009-2025 Service Manual / Engine Control/Fuel System / Engine Control System / Heated Oxygen Sensor (HO2S) Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the HO2S connector.
3.
Measure resistance between the HO2S terminals 3 and 4.
4.
Check that the resistance is within the specification.
Specification: Refer to “Specification”
Removal
[Bank 1/Sensor 1]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) cable.
2.
Disconnect the heated oxygen sensor connector.
3.
Lift the vehicle.
4.
Remove the heater protector (B) from the catalytic converter after removing the bolt (A).
5.
Remove the heated oxygen sensor (C) with the spanner after lifting the heater protector (B).

[Bank 1/Sensor 2]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) cable.
2.
Disconnect the heated oxygen sensor connector (B).
3.
Lift the vehicle.
4.
Remove the heated oxygen sensor (A).

[Bank 2/Sensor 1, Bank 2/Sensor 2]
1.
Turn the ignition switch OFF and disconnect the battery negative (-) cable.
2.
Lift the vehicle.
3.
Disconnect the heated oxygen sensor connector (A).
4.
Remove the heated oxygen sensor (B).
[Bank 2/Sensor 1]

[Bank 2/Sensor 2]

Installation
   
•
Install the component with the specified torques.
•
Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing.
   
•
DON’T use a cleaner, spray, or grease to sensing element and connector of the sensor because oil component in them may malfunction the sensor performance.
•
Sensor and its wiring may be damaged in case of contacting with the exhaust system (Exhaust Manifold, Catalytic Converter, and so on).
1.
Install in the reverse order of removal.
Heated oxygen sensor installation:
39.2 ~ 49.1 N.m (4.0 ~ 5.0 kgf.m, 28.9 ~ 36.2 lb-ft)
    Heated Oxygen Sensor (HO2S) Schematic Diagrams
    Circuit Diagram ...

    Accelerator Position Sensor (APS) Description and Operation
    Description Accelerator Position Sensor (APS) is installed on the accelerator pedal module and detects the rotation angle of the accelerator pedal. The APS is one of the most important sensors ...

    See also:

    35R Clutch Control Solenoid Valve(35R/C_VFS) Repair procedures
    Inspection 1. Turn ignition switch OFF. 2. Disconnect the E Module connector. 3. Measure resistance between sensor signal terminal and sensor ground terminal. 4. Check that the res ...

    To control the vehicle height
    Push the vehicle height control button to select the HIGH mode that makes the vehicle higher than the NORMAL mode and the indicator light on the vehicle height control button will illuminate. It i ...

    8LR Brake Control Solenoid Valve Specifications
    Specifications Direct control VFS[8LR/B] x Control Type : Normal low type Control Pressure kpa (kgf/cmx, psi)0 ~ 2108.42(0 ~ 21.5, 0 ~ 305.80)Current value(mA)0~1100 Internal r ...

    Categories

    Hyundai Equus Manuals


    © 2011-2025 Copyright www.heqmanual.com