>

Hyundai Equus: Rear Door Side Curtain Description and Operation - Rear Curtain System - Body Electrical System - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Rear Door Side Curtain Description and Operation

Overview
Rear door curtains shield the vehicle’s inside from sunlight and provides privacy for rear passengers.
-
Switch-operated power curtains (rear LH and RH doors).
-
Rear curtain switch and power window switch is a single unit.
-
Rear door curtain control is available at the driver’s seat as well.
-
Both rear LH and RH passengers can control both rear door curtains.
Door Curtain ECU
The door curtain ECU determines whether the curtain should be raised or lowered based on digital RLDM (RRDM) switch and motor sensor signals. In addition, the ECU monitors whether or not the curtain has been completely lowered or is in the process of rising.
Drive Unit
The drive unit features a sensor that detects the curtain’s movement and direction of movement, a motor, and a gearbox designed to leverage the motor’s power. The motor pushes or pulls flexible antenna wires to raise or lower the curtain. Lastly, a flap door has been added to the top section of the door trim to neatly stow the curtain away when not in use.
Switches
1.
Remote Operation
DDM can be used to remotely operate the rear windows and curtains. RLDM (RRDM) analyzes switch operation signals to determine whether the window or the curtain needs to be operated.
RLDM (RRDM) features two switches. The 2 switches control the concerned door’s window and curtain, whereas the switch toward the interior of the vehicle controls the opposite door’s window and curtain (via a serial communication line).
2.
Switch Operation
Power window and curtain switches operate as follows:
Category
Pull (1 click)
Pull (2 clicks)
Push (1 click)
Push (2 clicks)
Window
Manual Up
Auto Up
Manual Down
Auto Down
Door Curtain
Auto Up
Auto Down
Note
Door curtain control signals automatically raise or lower the curtain, regardless of
whether it was a 1-click or a 2-click.

3.
DDM and RLDM (RRDM) Switch Controls
DDM and RLDM (RRDM) controls are as follows:
Window
Position
Curtain
Position
Window Switch
DDM
Off
Manual Up
Manual
Down
Auto Up
Auto Down
Closed
Up
RLDM
RRDM
Off
-
Up
Down
Up
Down
Manual Up
Up
Up
-
Up
-
Manual
Down
Down
-
Down
-
Down
Auto Up
Up
Up
-
Up
-
Auto Down
Down
-
Down
-
Down
Down
RLDM
RRDM
Off
-
Up
-
Up
-
Manual Up
Up
Up
-
Up
-
Manual
Down
-
-
-
-
-
Auto Up
Up
Up
-
Up
-
Auto Down
-
-
-
-
-

Curtain Control Time Chart
1.
Curtain Switch Input
All signals received while switch operation is in progress are ignored.

2.
Reverse Signal
If a reverse signal is entered while the curtain is being lowered or raised, the reverse signal will immediately override the current action regardless of whether or not the action has completed.

Safety Feature
If an object is detected while the curtain is being raised, the curtain will immediately stop and revert back down to the fully lowered position.
Detection Zone
Detection Force
Action

* Center of upper curtain profile.
100N
Fully lower the curtain.

Reset
System reset essentially resets the curtain position to improve precision. The system can be reset either manually or automatically.
1.
Automatic Reset
RLDM (RRDM) automatically resets the curtain after every 200th operation to relearn curtain position data.
2.
Manual Reset
If curtain operation seems imprecise, manually reset the system to recalibrate curtain position data. Hold the window switch in the up position for ten seconds.
   
1)
Does not reset during auto up.
2)
The system can be reset from DDM, RLDM or RRDM (Except ADM).
Rear Door Curtain Reset Procedure
Manual Reset

x There is no realation with window glass position.
Manual Reset Procedure
-
When door curtain position is bottom : Curtain UP > FULL expansion > Curtain DOWN > Reset complete
-
When door curtain position is top : Curtain DOWN > Curtain UP > FULL expansion > Curtain DOWN > Reset complete
Caution In Manual Reset Procedure
1.
Hold the window switch in the 1 click UP state (Manual Up) for 10 seconds then manual reset procedure is started.
A.
There is no realation with window glass position
2.
Make sure that IGN ON during manual reset procedure.
A.
There should be occurred error in ACC or IGN OFF because of low voltage.
3.
If another switch module interrupt the reset procedure switch(during 10 seconds), reset procedure is canceled.
ex) If RRDM curtain is operated by RLDM switch during RRDM manual reset procedure, RRDM reset is canceled.
4.
Do not operate the rear door curtain during manual reset procedure.
    Rear Door Side Curtain Schematic Diagrams
    Circuit Diagram ...

    Rear Door Side Curtain Repair procedures
    Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the front door trim. (Refer to Body - "Front door trim") 3. Disconnect the rear door side curtain connector (A). 4. ...

    See also:

    Components and Components Location
    Component Location 1. AVN head unit2. Front LCD monitor3. Blue Link keyboard (Option)4. AUX jack5. Rear monitor spliter6. Steering wheel remote controller (SWRC)7. AVN rear keyboard8. External am ...

    Advanced smart cruise control system (If equipped)
    (1) CRUISE indicator (2) SET indicator (3) Set speed (4) Vehicle-to-vehicle distance The smart cruise control system allows you to program the vehicle to maintain a set speed so long as it is ...

    Manifold Absolute Pressure Sensor (MAPS) Description and Operation
    Description Manifold Absolute Pressure Sensor (MAPS) is a speed-density type sensor and is installed on the surge tank. It senses absolute pressure of the surge tank and transfers the analog si ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com