Hyundai Equus: Specifications
| Specification |
| Items | Inner side | Outer side | |
| Rear driveshaft | Joint type | Cross grove(VL) | Cross grove(VL) |
| Max. permissible angle | 21° | 21° | |
| Differential | Oil type | Hypoid gear oil MS 517-15 GT (SAE 75W/90, API GL-5, SHELL SPIRAX X Equivalent) | |
| Oil capacity (x) | 1.4 ± 0.05 | ||
| Reduction gear type | Hypoid gear | ||
| Reduction gear ratio | LAMMDA : 3.909, TAU : 3.538 | ||
| Final drive gear backlash mm(in.) | 0.10 ~ 0.15 | ||
| Differential gear backlash mm(in.) | 0 ~ 0.076 | ||
Tightening Torque
| Items | Nm | kgf.m | lb-ft | |
| Front | Wheel nut | 88.3 ~ 107.9 | 9.0 ~ 11.0 | 65.1 ~ 79.6 |
| Driveshaft castle nut | 196.1 ~ 255.0 | 20.0 ~ 26.0 | 144.7 ~ 188.1 | |
| Strut assembly lower mounting bolt | 152.0 ~ 171.6 | 15.5 ~ 17.5 | 112.1 ~ 126.6 | |
| Inner shaft bearing bracket bolt | 49.0 ~ 68.6 | 5.0 ~ 7.0 | 36.2 ~ 50.6 | |
| brake caliper mounting bolt | 98.1 ~ 117.7 | 10.0 ~ 12.0 | 72.3 ~ 86.8 | |
| Wheel speed sensor mounting bolt | 6.9 ~ 10.8 | 0.7 ~ 1.1 | 5.1 ~ 8.0 | |
| brake disc mounting screw | 4.9 ~ 5.9 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
| Hub assembly mounting bolt | 78.5 ~ 98.1 | 8.0 ~ 10.0 | 57.9 ~ 72.3 | |
| Lower arm ball joint mounting bolt | 137.2 ~ 156.9.7 | 14.0 ~ 16.0 | 101.2 ~ 115.7 | |
| Tension arm mounting nut | 88.3 ~ 107.9 | 9.0 ~ 11.0 | 65.1 ~ 79.5 | |
| Lateral arm mounting nut | 88.3 ~ 107.9 | 9.0 ~ 11.0 | 65.1 ~ 79.6 | |
| Tie rod end ball joint mounting nut | 88.3 ~ 107.9 | 9.0 ~ 11.0 | 65.1 ~ 79.5 | |
| Rear | Wheel nut | 88.3 ~ 107.9 | 9.0 ~ 11.0 | 65.1 ~ 79.6 |
| Driveshaft castle nut | 196.1 ~ 274.5 | 20.0 ~ 28.0 | 144.7 ~ 202.5 | |
| Shock absorber lower mounting bolt | 137.3 ~ 156.9 | 14.0 ~ 16.0 | 101.3 ~ 115.7 | |
| brake caliper mounting bolt | 63.7 ~ 73.5 | 6.5 ~ 7.5 | 47.0 ~ 54.2 | |
| Wheel speed sensor mounting bolt | 6.9 ~ 10.8 | 0.7 ~ 1.1 | 5.1 ~ 8.0 | |
| brake disc mounting screw | 4.9 ~ 5.9 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
| Hub assembly mounting bolt | 78.5 ~ 98.1 | 8.0 ~ 10.0 | 72.3 ~ 65.1 | |
| Upper arm ball joint mounting nut | 78.5 ~ 88.3 | 8.0 ~ 9.0 | 57.9 ~ 65.1 | |
| Lower arm mounting bolt | 137.3 ~ 156.9 | 14.0 ~ 16.0 | 101.3 ~ 115.7 | |
| Assist arm ball joint mounting nut | 78.5 ~ 88.3 | 8.0 ~ 9.0 | 57.9 ~ 65.1 | |
| Trailing arm mounting bolt | 98.1 ~ 117.7 | 10.0 ~ 12.0 | 72.3 ~ 86.8 | |
| Propellershaft | Front propeller shaft mounting bolt | 88.2 ~ 107.8 | 9.0 ~ 11.0 | 65.0 ~ 79.5 |
| Propeller shaft center bearing bracket mounting bolt | 49.0 ~ 63.7 | 5.0 ~ 6.5 | 36.1 ~ 47.0 | |
| Rear propeller shaft mounting bolt | 88.2 ~ 107.8 | 9.0 ~ 11.0 | 65.0 ~ 79.5 | |
| Differential | Rear differential mounting bolt | 68.6 ~ 88.3 | 7.0 ~ 9.0 | 50.6 ~ 65.1 |
| Differential cover mounting bolt | 39.2 ~ 49.0 | 4.0 ~ 5.0 | 28.9 ~ 36.2 | |
Replace self-locking nuts with new ones after removal. |
| Lubricants |
| Items | Lubricants | Quantity | |
| Rear driveshaft | Cross grove(VL) | 2L~584/LD | 85 ± 10g |
| Cross grove(VL) | 2L~584/LD | 85 ± 10g | |
Special Service Tools
Special Service Tools
Tool(Number and Name)IllustrationUse09581-11000Piston expanderSpreading the front disc brake piston.09568-2J100Ball joint removerRemoval of the rear assist arm and tie rod e ...
See also:
Sunroof Glass Components and Components Location
Component Location
1. Sunroof glass
...
Auto Defogging Sensor Repair procedures
Inspection
To inspect and diagnose the sensor, refer to Self-Diagnosis procedure and DTC guide.
Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remov ...
Intake Actuator Repair procedures
Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the intake actuator connector.
3.
Verify that the intake actuator operates to the fresh position when connecting 12V to terminal 3 ...
Categories
Hyundai Equus Manuals
© 2011-2024 Copyright www.heqmanual.com