>
Hyundai Equus Manuals

Hyundai Equus: Console Temperature Control Actuator Repair procedures - Heater - Heating, Ventilation and Air Conditioning - Hyundai Equus VI 2009-2024 Service ManualHyundai Equus: Console Temperature Control Actuator Repair procedures

Second generation VI (2009–2024) / Hyundai Equus VI 2009-2024 Service Manual / Heating, Ventilation and Air Conditioning / Heater / Console Temperature Control Actuator Repair procedures

Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the console temperature control actuator connector.
3.
Verify that the console temperature control actuator operates to the defrost mode when connecting 12V to terminal 3 and grounding terminal 4.
Verify that the console actuator operates to the vent mode when connected in reverse.

1. -
2. -
3. Cool position
4. Warm position
5. Sensor ground
6. Feedback signal
7. Sensor (+ 5V)

4.
Connect the console actuator connector.
5.
Turn the ignition switch ON.
6.
Check the voltage between terminal 6 and 5.
Specification
Door position
Voltage (V) 
Error detecting
Cooling
3.8 ± 0.15
 Low voltage : 0.1V or less
Heating
1.2 ± 0.15
 High voltage : 4.9V or more

It will feedback the current position of the actuator to contorls.
7.
If the measured voltage is not within specification, substitute with a known-good console temperature control actuator and check for proper operation.
8.
Replace the console temperature control actuator if it is proved that there is a problem with it.
Replacement
[Console Temperature Control Actuator (A)]
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remover, remove the driver's side crash pad side cover.

3.
After loosening the mounting screws, remove the crash pad lower panel (A).

4.
Disconnect the crash pad lower panel switch connector (A) and knee air bag connector (B).

5.
Remove the driver's side shower duct (A) after loosening the screw.

6.
Disconnect the connector (A) and then remove the console temperature control actuator (B) after loosening the mounting screws.

7.
Install in the reverse order of removal.
[Console Temperature Control Actuator]
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remover, remove the driver's side crash pad side cover.

3.
After loosening the mounting screws, remove the crash pad lower panel (A).

4.
Disconnect the crash pad lower panel switch connector (A) and knee air bag connector (B).

5.
Remove the driver's side shower duct (A) after loosening the screw.

6.
Disconnect the console temperature control actuator connector (A), and then remove the temperature control actuator (B) after loosening the mounting screws.

7.
Install in the reverse order of removal.
    Mode Control Actuator Repair procedures
    Inspection 1. Turn the ignition switch OFF. 2. Disconnect the mode control actuator connector. 3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to ...

    Auto Defogging Actuator Description and Operation
    Description The auto defogging sensor is installed on front window glass. The sensor judges and sends signal if moisture occurs to blow out wind for defogging. The air conditioner control modul ...

    See also:

    General Safety Information and Caution
    Instructions When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be ...

    Front Door Trim Components and Components Location
    Component Location 1. Front door trim ...

    Hood Seal Weatherstrip Repair procedures
    Replacement 1. Detach the clips, then remove the hood seal weatherstrip (A).     • Be careful not to scratch the hood seal weatherstrip. 2. Installation is the rever ...

    Categories

    Hyundai Equus Manuals


    © 2011-2024 Copyright www.heqmanual.com